Ghostbusters Attenuator 2.0 with Universal Proton Pack on/off and manual vent control - Adam Savage Inspired
from $200.00
Sold Out
Important Information about Attenuator 2.0, please read and ask any questions before ordering.
Downloadable instructions can be found at
https://rightcoastcreative.com/attenuator2
Attenuator 2.0 was designed to be universal and is compatible with both the STOCK electronics Haslab proton packs and the Ninjatunes electronics upgraded Haslab proton packs. However, it is truly universal and could be adapted to other proton pack kits with some adaptation by the end user.
Attenuator 2.0 is available in 4 different kit variants.
1. Complete with venting control
2. Complete without venting control
3. Build your own with venting control
4. Build your own without venting control
Depending on which kit variant you purchase, you may not use all wire connections or included parts, but parts are still included for future use or future adaptations.
When attenuator 2.0 is installed on a STOCK electronics Haslab proton pack, it will function as a keep alive kit for the pack only and keep the pack running indefinitely.
IMPORTANT: Attenuator 2.0 is not designed to work with other keep alive mods for the pack or wand and is not recommended to be used with them. I assume no liability for adverse effects, damage or unintended outcomes due to experimentation of Attenuator 2.0 with other electronic pack modifications.
Attenuator 2.0 is designed to run on 5 volts only. DO NOT run power greater than 5 volts or damage to the electronics will occur.
The venting control module is just a simple relay and the output acts as a switch. The wiring output in the kit is made specifically for the Haslab and Ninjatunes boards. If you want to use Attenuator 2.0 on a different kit, you can replace the output wiring of the relay with a standard two wire connector.
Connection from the Attenuator 2.0 to the Proton Pack uses a 4 pin GX16 connector and cable set up, commonly called an “Aviation Cable” and is listed as such throughout the instructions.
When vent mode is toggled, venting acts the same as when the ribbon cable is removed from the cyclotron. The Haslab proton pack will make the containment unit failure sound effect. The Ninjatunes kit will trigger the Ninjatunes vent relay and optional smoke kit (if installed).
On Ninjatunes, if your wand is on, manual venting is not possible. This is because of the programming of the Ninjatunes board, it will override manual venting when it senses the wand is active in preparation for overheat venting of the wand.
Please remember, this is a hand built prop and is 3D printed in PLA plastic, there will be some imprecations and variations from attenuator to attenuator due to the custom built process. Exposure to extreme temperatures or left in hot cars for long periods of time can cause issues with plastics and warping.
Please allow time for building, assembly and shipping. While I do have plenty of parts on hand to build these attenuators, each one is built to order at the time of order with available parts on hand.
If damage occurs during shipping, contact me immediately.
Thank you!
Downloadable instructions can be found at
https://rightcoastcreative.com/attenuator2
Attenuator 2.0 was designed to be universal and is compatible with both the STOCK electronics Haslab proton packs and the Ninjatunes electronics upgraded Haslab proton packs. However, it is truly universal and could be adapted to other proton pack kits with some adaptation by the end user.
Attenuator 2.0 is available in 4 different kit variants.
1. Complete with venting control
2. Complete without venting control
3. Build your own with venting control
4. Build your own without venting control
Depending on which kit variant you purchase, you may not use all wire connections or included parts, but parts are still included for future use or future adaptations.
When attenuator 2.0 is installed on a STOCK electronics Haslab proton pack, it will function as a keep alive kit for the pack only and keep the pack running indefinitely.
IMPORTANT: Attenuator 2.0 is not designed to work with other keep alive mods for the pack or wand and is not recommended to be used with them. I assume no liability for adverse effects, damage or unintended outcomes due to experimentation of Attenuator 2.0 with other electronic pack modifications.
Attenuator 2.0 is designed to run on 5 volts only. DO NOT run power greater than 5 volts or damage to the electronics will occur.
The venting control module is just a simple relay and the output acts as a switch. The wiring output in the kit is made specifically for the Haslab and Ninjatunes boards. If you want to use Attenuator 2.0 on a different kit, you can replace the output wiring of the relay with a standard two wire connector.
Connection from the Attenuator 2.0 to the Proton Pack uses a 4 pin GX16 connector and cable set up, commonly called an “Aviation Cable” and is listed as such throughout the instructions.
When vent mode is toggled, venting acts the same as when the ribbon cable is removed from the cyclotron. The Haslab proton pack will make the containment unit failure sound effect. The Ninjatunes kit will trigger the Ninjatunes vent relay and optional smoke kit (if installed).
On Ninjatunes, if your wand is on, manual venting is not possible. This is because of the programming of the Ninjatunes board, it will override manual venting when it senses the wand is active in preparation for overheat venting of the wand.
Please remember, this is a hand built prop and is 3D printed in PLA plastic, there will be some imprecations and variations from attenuator to attenuator due to the custom built process. Exposure to extreme temperatures or left in hot cars for long periods of time can cause issues with plastics and warping.
Please allow time for building, assembly and shipping. While I do have plenty of parts on hand to build these attenuators, each one is built to order at the time of order with available parts on hand.
If damage occurs during shipping, contact me immediately.
Thank you!
Attenuator 2.0:
Important Information about Attenuator 2.0, please read and ask any questions before ordering.
Downloadable instructions can be found at
https://rightcoastcreative.com/attenuator2
Attenuator 2.0 was designed to be universal and is compatible with both the STOCK electronics Haslab proton packs and the Ninjatunes electronics upgraded Haslab proton packs. However, it is truly universal and could be adapted to other proton pack kits with some adaptation by the end user.
Attenuator 2.0 is available in 4 different kit variants.
1. Complete with venting control
2. Complete without venting control
3. Build your own with venting control
4. Build your own without venting control
Depending on which kit variant you purchase, you may not use all wire connections or included parts, but parts are still included for future use or future adaptations.
When attenuator 2.0 is installed on a STOCK electronics Haslab proton pack, it will function as a keep alive kit for the pack only and keep the pack running indefinitely.
IMPORTANT: Attenuator 2.0 is not designed to work with other keep alive mods for the pack or wand and is not recommended to be used with them. I assume no liability for adverse effects, damage or unintended outcomes due to experimentation of Attenuator 2.0 with other electronic pack modifications.
Attenuator 2.0 is designed to run on 5 volts only. DO NOT run power greater than 5 volts or damage to the electronics will occur.
The venting control module is just a simple relay and the output acts as a switch. The wiring output in the kit is made specifically for the Haslab and Ninjatunes boards. If you want to use Attenuator 2.0 on a different kit, you can replace the output wiring of the relay with a standard two wire connector.
Connection from the Attenuator 2.0 to the Proton Pack uses a 4 pin GX16 connector and cable set up, commonly called an “Aviation Cable” and is listed as such throughout the instructions.
When vent mode is toggled, venting acts the same as when the ribbon cable is removed from the cyclotron. The Haslab proton pack will make the containment unit failure sound effect. The Ninjatunes kit will trigger the Ninjatunes vent relay and optional smoke kit (if installed).
On Ninjatunes, if your wand is on, manual venting is not possible. This is because of the programming of the Ninjatunes board, it will override manual venting when it senses the wand is active in preparation for overheat venting of the wand.
Please remember, this is a hand built prop and is 3D printed in PLA plastic, there will be some imprecations and variations from attenuator to attenuator due to the custom built process. Exposure to extreme temperatures or left in hot cars for long periods of time can cause issues with plastics and warping.
Please allow time for building, assembly and shipping. While I do have plenty of parts on hand to build these attenuators, each one is built to order at the time of order with available parts on hand.
If damage occurs during shipping, contact me immediately.
Thank you!
Downloadable instructions can be found at
https://rightcoastcreative.com/attenuator2
Attenuator 2.0 was designed to be universal and is compatible with both the STOCK electronics Haslab proton packs and the Ninjatunes electronics upgraded Haslab proton packs. However, it is truly universal and could be adapted to other proton pack kits with some adaptation by the end user.
Attenuator 2.0 is available in 4 different kit variants.
1. Complete with venting control
2. Complete without venting control
3. Build your own with venting control
4. Build your own without venting control
Depending on which kit variant you purchase, you may not use all wire connections or included parts, but parts are still included for future use or future adaptations.
When attenuator 2.0 is installed on a STOCK electronics Haslab proton pack, it will function as a keep alive kit for the pack only and keep the pack running indefinitely.
IMPORTANT: Attenuator 2.0 is not designed to work with other keep alive mods for the pack or wand and is not recommended to be used with them. I assume no liability for adverse effects, damage or unintended outcomes due to experimentation of Attenuator 2.0 with other electronic pack modifications.
Attenuator 2.0 is designed to run on 5 volts only. DO NOT run power greater than 5 volts or damage to the electronics will occur.
The venting control module is just a simple relay and the output acts as a switch. The wiring output in the kit is made specifically for the Haslab and Ninjatunes boards. If you want to use Attenuator 2.0 on a different kit, you can replace the output wiring of the relay with a standard two wire connector.
Connection from the Attenuator 2.0 to the Proton Pack uses a 4 pin GX16 connector and cable set up, commonly called an “Aviation Cable” and is listed as such throughout the instructions.
When vent mode is toggled, venting acts the same as when the ribbon cable is removed from the cyclotron. The Haslab proton pack will make the containment unit failure sound effect. The Ninjatunes kit will trigger the Ninjatunes vent relay and optional smoke kit (if installed).
On Ninjatunes, if your wand is on, manual venting is not possible. This is because of the programming of the Ninjatunes board, it will override manual venting when it senses the wand is active in preparation for overheat venting of the wand.
Please remember, this is a hand built prop and is 3D printed in PLA plastic, there will be some imprecations and variations from attenuator to attenuator due to the custom built process. Exposure to extreme temperatures or left in hot cars for long periods of time can cause issues with plastics and warping.
Please allow time for building, assembly and shipping. While I do have plenty of parts on hand to build these attenuators, each one is built to order at the time of order with available parts on hand.
If damage occurs during shipping, contact me immediately.
Thank you!
Important Information about Attenuator 2.0, please read and ask any questions before ordering.
Downloadable instructions can be found at
https://rightcoastcreative.com/attenuator2
Attenuator 2.0 was designed to be universal and is compatible with both the STOCK electronics Haslab proton packs and the Ninjatunes electronics upgraded Haslab proton packs. However, it is truly universal and could be adapted to other proton pack kits with some adaptation by the end user.
Attenuator 2.0 is available in 4 different kit variants.
1. Complete with venting control
2. Complete without venting control
3. Build your own with venting control
4. Build your own without venting control
Depending on which kit variant you purchase, you may not use all wire connections or included parts, but parts are still included for future use or future adaptations.
When attenuator 2.0 is installed on a STOCK electronics Haslab proton pack, it will function as a keep alive kit for the pack only and keep the pack running indefinitely.
IMPORTANT: Attenuator 2.0 is not designed to work with other keep alive mods for the pack or wand and is not recommended to be used with them. I assume no liability for adverse effects, damage or unintended outcomes due to experimentation of Attenuator 2.0 with other electronic pack modifications.
Attenuator 2.0 is designed to run on 5 volts only. DO NOT run power greater than 5 volts or damage to the electronics will occur.
The venting control module is just a simple relay and the output acts as a switch. The wiring output in the kit is made specifically for the Haslab and Ninjatunes boards. If you want to use Attenuator 2.0 on a different kit, you can replace the output wiring of the relay with a standard two wire connector.
Connection from the Attenuator 2.0 to the Proton Pack uses a 4 pin GX16 connector and cable set up, commonly called an “Aviation Cable” and is listed as such throughout the instructions.
When vent mode is toggled, venting acts the same as when the ribbon cable is removed from the cyclotron. The Haslab proton pack will make the containment unit failure sound effect. The Ninjatunes kit will trigger the Ninjatunes vent relay and optional smoke kit (if installed).
On Ninjatunes, if your wand is on, manual venting is not possible. This is because of the programming of the Ninjatunes board, it will override manual venting when it senses the wand is active in preparation for overheat venting of the wand.
Please remember, this is a hand built prop and is 3D printed in PLA plastic, there will be some imprecations and variations from attenuator to attenuator due to the custom built process. Exposure to extreme temperatures or left in hot cars for long periods of time can cause issues with plastics and warping.
Please allow time for building, assembly and shipping. While I do have plenty of parts on hand to build these attenuators, each one is built to order at the time of order with available parts on hand.
If damage occurs during shipping, contact me immediately.
Thank you!
Downloadable instructions can be found at
https://rightcoastcreative.com/attenuator2
Attenuator 2.0 was designed to be universal and is compatible with both the STOCK electronics Haslab proton packs and the Ninjatunes electronics upgraded Haslab proton packs. However, it is truly universal and could be adapted to other proton pack kits with some adaptation by the end user.
Attenuator 2.0 is available in 4 different kit variants.
1. Complete with venting control
2. Complete without venting control
3. Build your own with venting control
4. Build your own without venting control
Depending on which kit variant you purchase, you may not use all wire connections or included parts, but parts are still included for future use or future adaptations.
When attenuator 2.0 is installed on a STOCK electronics Haslab proton pack, it will function as a keep alive kit for the pack only and keep the pack running indefinitely.
IMPORTANT: Attenuator 2.0 is not designed to work with other keep alive mods for the pack or wand and is not recommended to be used with them. I assume no liability for adverse effects, damage or unintended outcomes due to experimentation of Attenuator 2.0 with other electronic pack modifications.
Attenuator 2.0 is designed to run on 5 volts only. DO NOT run power greater than 5 volts or damage to the electronics will occur.
The venting control module is just a simple relay and the output acts as a switch. The wiring output in the kit is made specifically for the Haslab and Ninjatunes boards. If you want to use Attenuator 2.0 on a different kit, you can replace the output wiring of the relay with a standard two wire connector.
Connection from the Attenuator 2.0 to the Proton Pack uses a 4 pin GX16 connector and cable set up, commonly called an “Aviation Cable” and is listed as such throughout the instructions.
When vent mode is toggled, venting acts the same as when the ribbon cable is removed from the cyclotron. The Haslab proton pack will make the containment unit failure sound effect. The Ninjatunes kit will trigger the Ninjatunes vent relay and optional smoke kit (if installed).
On Ninjatunes, if your wand is on, manual venting is not possible. This is because of the programming of the Ninjatunes board, it will override manual venting when it senses the wand is active in preparation for overheat venting of the wand.
Please remember, this is a hand built prop and is 3D printed in PLA plastic, there will be some imprecations and variations from attenuator to attenuator due to the custom built process. Exposure to extreme temperatures or left in hot cars for long periods of time can cause issues with plastics and warping.
Please allow time for building, assembly and shipping. While I do have plenty of parts on hand to build these attenuators, each one is built to order at the time of order with available parts on hand.
If damage occurs during shipping, contact me immediately.
Thank you!
